www.rgc.ro Web analytics

Jump to content

Tremolo arm


Guest spyked88

Recommended Posts

Guest spyked88

... cred cã în general posesorii de strat-uri s-au lovit de problema asta, pe care m-am hotãrât sã o rezolv, aºa cã apelez la sfatul vostru. Sã n-o mai lungesc, trec direct la întrebare: ce tratament pot aplica brațului de la tremolo (repet, e vorba de vintage tremolo, tipic stratocaster) sã nu se mai bãlãngãne ca nebunul de fiecare datã când îi dau drumul din mânã? Vreau sã stea într-un loc ºi sã se miºte doar când îl dau eu într-o parte, nu în virtutea inerției.

 

Pe google nu am gãsit mai nimic concret, dar dacã are cineva un link, i-aº fi recunoscãtor.

Link to comment
Share on other sites

Guest spyked88

Nu cred cã merge aºa. Am încercat sã îl înºurubez la limitã, ºi ajunge la un punct în care nu se mai miºcã deloc, deci se blocheazã acolo. În punctul ãla, dacã îl dezºurubez un pic, iar se miºcã de capul lui. Nici nu mã gândesc sã îl forțez, fiindcã nu vreau sã rãmân cu brațul în douã bucãți.

Link to comment
Share on other sites

Aha, inseamna ca are joc. Vezi ca gasesti site-uri care iti arata cum se seteaza tremolo-ul.

 

Tremolo

 

Stratocasters can be found with four distinctive types of bridges. The most well known bridge is the vintage style "synchronized" tremolo. The other three are the American Standard bridge, which is a modern-day two-pivot bridge, the non-tremolo hardtail bridge, and the locking tremolo such as the American Deluxe or Floyd Rose® locking tremolos. If you have a non-tremolo "hardtail" bridge, proceed to Intonation (Roughing it out). If you have a locking tremolo bridge click here.

 

First, remove the tremolo back cover. Check your tuning. Let’s start with a vintage style tremolo bridge. Here’s a great tip to enhance the performance of this bridge: Using your tremolo arm, pull the bridge back flush with the body. Loosen all six screws located at the front edge of the bridge plate. Raise them so that all of the screws measure approximately 1/16" (1.6 mm) above the top of the bridge plate. Finally, tighten the two outside screws back down until they are flush with the top of the bridge plate. The bridge will now pivot on the outside screws, leaving the four inside screws in place for bridge stability. For a two-pivot bridge like the American Standard bridge use your tremolo arm to pull the bridge back flush with the body and adjust the two pivot screws to the point where the tremolo plate sits entirely flush at the body (not lifted at the front or back of the plate).

 

Allowing the bridge to float freely (no tension on the tremolo arm) using the claw screws in the tremolo cavity, adjust the bridge to your desired angle (Fender spec. is 1/8" (3.2 mm) gap at rear of bridge). You will need to retune periodically to get the right balance between the strings and the springs. If you prefer a flush bridge to body, adjust spring tension to equal string tension, while the bridge rests on body (you may want to put an extra 1/2 turn to each claw screw to ensure that the bridge remains flush to the body during string bends). Caution: Do not over-tighten the springs as it can put unnecessary tension on the arm during tremolo use. Finally, you may wish to apply a small dab of Chapstick® or Vaseline® at the pivot contact points of the bridge for a very smooth operation.

Link to comment
Share on other sites

Exista un fel de gel care face ce spui tu. Am sa ma interesez cum se numeste.

exista blue tack,produs de bostik,un fel de plastilina,am pus-o pe filetul de la maneta si gata.se gaseste la papetariile mari,de ex.la Diverta,e ambalat intr-un plic cam 10 pe 15 cm.

Link to comment
Share on other sites

Poti infige un bat de "cribit"... poti pune clei de copac, zeama de pepene pentru ca e lipicioasa, sa scoti maneta de "verb" si sai dai un ciocan in filet sa se mai aranjeze spirele alea, poti monta manetuta si cand o pui intr-o pozitie buna de lucru, bagi o sudura. Nu o sa mai iasa in veci de acolo!

Atentie foloseste autogenul si nu aparatul de sudurua electric!!! Poti demonta mecanismul ca flacara sa nu-ti afecteze lemnul chitarii.

Link to comment
Share on other sites

  • 3 weeks later...
Guest fluffyone

Am vazut o smecherie care presupun totusi ca e banala dar functioneaza. Tine-l putin la o bricheta sau alta sursa deschisa de caldura inainte sa il bagi in chitara.

Link to comment
Share on other sites

Guest fluffyone

in perioada asta, o parte din problemele astea vin de la frig. Hardware-ul de pe JEM e foarte sensibil dar dupa o runda de foc cu o bricheta isi revine. Da, teoretic si in mare masura si practic se contracta la loc, cand se receste, dar se raceste ceva mai greu si nici cu legile alea de caldura nu e chiar cum scrie la carte. Incercati, poate va ajuta.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...

Important Information

"This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies.